i would say yes......2 1/2 inch groups are fine and you still have some room to spare. i know the feeling though about wanting better, dont want to take the chance of only wounding something, but i would be ok with 2 1/2. just wondering, do u use a scope or red dot or factory sights?
I checked everything on the crossbow Stan. Everything appears to be in order. The trigger on the Horton is atrocious though. Easy to pull a shot due to the travel and weight of pull. But, I used to shoot a bit better than I have recently. I'm not overly concerned with the groups. But, I'm like you and expect near perfection, which is a tall order. I didn't shoot much better today with unbladed Muzzy tips than I did with the same tips after attaching the blades. So the broadheads were not a big factor. I've noticed my groups with my rimfire rifles aren't what they used to be either. I think it is just part of aging catching up with me. Keeping my shots to twenty yards and under with my crossbow is what I have always done. I guess my fear is what Bambilastbreath touched on, wounding an animal and not recovering it.
I am using a Bushnell 3-9 scope that I've used for 9 years on this crossbow. It holds zero very well. I always shoot on 3X whether hunting or target shooting. I try to simulate my hunting set ups when target shooting. All my stands are set up with some type of rest to steady my crossbow when shooting at a deer.
I may be opinionated...but, my opinion is the only one that matters anyway.
I would agree with Bambi on this. The 2 1/2 inch groups are good enough to kill a deer, just make sure you are putting it snug to the crease and let it go. At that distance anything on to the shoulder should penetrate very well and anything back a little will still be well within the boiler room.
Along the lines of this, last year my dad was all excited to bowhunt with my buddy and I. Well he pulled out his bow and found out that it was harder to pull than he remembered. After adjusting the draw weight down he said he was good to go. Well, we saw him shoot and boy did he struggle with drawing and shooting accurately. Felt bad for him because he was the one who taught me and boy was he a great shot. Offered to bring down our crossbow for him to use this year and he graciously accepted. Kind of think of it as an equalizer for him I hope. If I had the money I surely would be buying him one of his own.
well I am sure aging is and will get to us all at some point
but I do know that there can be things going on with equipment that the eye cannot see, and limbs are for sure one of them, have to always wonder , or I do, how long they can store energy and memory, as once lopaded thats a LOT of pressure being held on them in my eye's over yrs I HAVE to think they loose some of it, and wonder even more if they do so in an equal manor!
but I again agree your groups are plenty good to make clean kills
something you may or may not like, but mechanical heads that open to bigger size than your muzzys can help add a little extra give on shot placement too
them 2.5 inch Rage heads whould fly fibe from an X bow and at 20 yrds you would have tons of energy for a pass through
not one to say bigger is better, but it cannot hurt either
I know you like your fixed heads, and have trust in them, but it could be something to think about
and yes ALL X bow's to me could sure benefit from better factory triggers
all the mroe so on some of the one's that cost so much money too!, don't really have to be lighter, just less over travel and cleaner breaking
they need like an accu trigger on them , so you can have an extra safety too and still have a good trigger
Chuck, I'm sure your dad could benefit from a crossbow. I feel that anything that can get or keep you in the game is what one should use.
Stan, the limbs are a good point. I shoot quite a bit over the course of a years time. And every time I hunt I have to shoot at the end of the hunt. So the limbs do get a workout. I had new limbs put on 3 years ago. I cock use a cocking device which insures a very consistent centering.
Yes, a 2 1/2" cutting surface can be forgiving and makes my 1" diameter Muzzys look puny. But I am confident with the performance of my Muzzys.
Yes an Accu Trigger would be a great feature. I have one on my Savage .17HMR and use it as pre set from the factory. Very satisfactory for a factory trigger.
I may be opinionated...but, my opinion is the only one that matters anyway.
Wondering....is it possible to maybe have a gunsmith modify the trigger pull on a crossbow?? Thought the same on ours that the kids use, that it's a little tough to pull.
I would think a GOOD smith could for sure, but WOULD THEY??
liability is a reason so many triggers suck, too many legal suits to scare off a lot of good work that could be done on the cheap too!
I used Muzzy's for YRS, and liked them, but to me over the last several yrs that I used them I just couldn't get them to fly like the older one's
so I have tried several different heads since then,. and am on the rage heads not, but just the crossbow one's , not the big 2.5'
but what I use are 150 grain heads , and fly true and have worked when I do my part
confidence is a good thing to have in your gear
I just gave that as an example as an option if ever wanted
I knew you were a Muzzy man!
There are currently 3 users browsing this thread. (0 members and 3 guests)
Posting Permissions
Reply With Quote